IPL g05c44be
D-15
SPI 54M
64MB
BIST0_0001-OK
[SPI_NOR]
MXP found at 0x0000f000
offset:00007000
Checksum OK

IPL_CUST g05c44be
runUBOOT()
[SPI_NOR]
MXP found at 0x0000f000
offset:00020000
 -Decompress BDMA XZ
 -Decompress BDMA XZ
XZ decomp_size=0x00049be4
 pvLoadAddr:23d00000
 pvRunAddr:23e00000
 -Verify CRC32 passed!
  decomp_size=0x00000000
Disable MMU and D-cache before jump to UBOOT▒

U-Boot 2015.01 (Nov 24 2022 - 17:53:59)

Version: I6g#######
I2C:   ready
DRAM:
WARNING: Caches not enabled
MMC:   MStar SD/MMC: 0
nor_flash_mxp allocated success!!
Flash is detected (0x0B03, 0xC8, 0x40, 0x17)
SF: Detected nor0 with total size 8 MiB
MXP found at mxp_offset[2]=0x0000F000, size=0x1000
env_offset=0x3F000 env_size=0x1000
Flash is detected (0x0B03, 0xC8, 0x40, 0x17)
SF: Detected nor0 with total size 8 MiB
In:    serial
Out:   serial
Err:   serial
Net:   MAC Address 00:00:B4:67:B7:76
Auto-Negotiation...
Link Status Speed:100 Full-duplex:1
sstar_emac
reset key up !!!
Init wifi gpio


Anjoy # printenv
baudrate=115200
bootargs=console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs ro init=/linuxrc LX_MEM=0x3fe0000 mma_heap=mma_heap_name0,miu=0,sz=0x152C000 mma_memblock_remove=1
bootcmd=sf probe 0;sf read 0x21000000 0x00040000 0x001C0000;bootm 0x21000000
bootdelay=0
builddate=202312281015
ethact=sstar_emac
ethaddr=00:00:B4:67:B7:76
fileaddr=21000000
filesize=70954c
fsversion=3.3.0.2
ipaddr=192.168.1.197
reset_key=up
sdupgrade=1
serverip=192.168.1.253
stderr=serial
stdin=serial
stdout=serial
version_kernel=MSTAR_I6B0_LINUX_335
version_rootfs=MSJ10_V1

Environment size: 602/4092 bytes


Anjoy # help
?       - alias for 'help'
aes     - Control Mstar AES engine
base    - print or set address offset
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
btime   - Show booting time
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
dbg     - set debug message level. Default level is INFO
dcache  - enable or disable data cache
debug   - Disable uart rx via PAD_DDCA to use debug tool
dhcp    - boot image via network using DHCP/TFTP protocol
dstar   - script via SD/MMC
eeprom  - EEPROM sub-system
env     - environment handling commands
estar   - script via network
estart  - EMAC start
exit    - exit script
false   - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fatsize - determine a file's size
go      - start application at address 'addr'
gpio    - Config gpio port
help    - print command description/usage
i2c     - I2C sub-system
icache  - enable or disable instruction cache
initDbgLevel- Initial varaible 'dbgLevel'
loop    - infinite loop on address range
macaddr - setup EMAC MAC addr
md      - memory display
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mssdmmc - Mstar SD/MMC IP Verification System
mstar   - script via TFTP
mw      - memory write (fill)
mxp     - MXP function for Mstar MXP partition
nm      - memory modify (constant address)
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
pwm     - Set 5000Hz duty 50% pwm waveform and use PAD_FUART_RX
Sample: pwm 0 100000 200000 14

reset   - Perform RESET of the CPU
riu     - riu  - riu command

run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
sdstar  - script via sd package
secauth - Control Sstar security authenticate sequence
setenv  - set environment variables
sf      - SPI flash sub-system
sfbin   - for uploading sf image to a server(via network using TFTP protocol)
showvar - print local hushshell variables
sigauth - Only verify digital signature and aes
srcfg   - sensor pin and mclk configuration.
test    - minimal test like /bin/sh
test_sig- Test runAuthenticate2

tftpboot- boot image via network using TFTP protocol
true    - do nothing, successfully
uart    - UART sub-system
udpbc   - Send or receive UDP broadcast to/from server using UDP protocol
version - print monitor, compiler and linker version

Anjoy # version

U-Boot 2015.01 (Nov 24 2022 - 17:53:59)
arm-buildroot-linux-uclibcgnueabihf-gcc.br_real (Buildroot 2017.08-g239d7d0) 4.9.4
GNU ld (GNU Binutils) 2.28.1