Распиновка площадок разъема UART (J1 / DEBUG) (слева направо): 1 - Tx 2 - Rx 3 - Gnd 4 - +3.3V === u-boot === Boot 2010.06-dirty (May 09 2014 - 15:00:56) Check spi flash controller v350... Found Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18 Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX" In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 hi3516c # help ? - alias for 'help' base - print or set address offset bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation echo - echo args to console getinfo - print hardware information go - start application at address 'addr' help - print command description/usage loadb - load binary file over serial line (kermit mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mtest - simple RAM read/write test mw - memory write (fill) nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables sf - SPI flash sub-system tftp - tftp - download or upload image via network using TFTP protocol version - print monitor version hi3516c # printenv bootcmd=sf probe 0;sf read 0x82000000 0x30000 0x300000;bootm 0x82000000 bootdelay=1 baudrate=115200 gateway=192.168.1.1 netmask=255.255.255.0 ipaddr=192.168.1.120 serverip=192.168.1.35 ethaddr=d0:22:12:88::88:88 BoardType=600102003-BV-H0203 mac= serialno= uuid= chiptype=hi3516c bootargs=mem=56M console=ttyAMA0,115200 root=/dev/mtdblock3 rootfstype=squashfs rw init=/init mtdparts=hi_sfc:128k(u-boot)ro,64k(env),3072k(kernel),4608k(rootfs),512k(config),-(app) sensortype=imx122 stdin=serial stdout=serial stderr=serial verify=n ver=U-Boot 2010.06-dirty (May 09 2014 - 15:00:56) Environment size: 652/65532 bytes === u-boot === === полная загрузка === U-Boot 2010.06-dirty (May 09 2014 - 15:00:56) Check spi flash controller v350... Found Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18 Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX" In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 16384 KiB hi_sfc at 0:0 is now current device ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.0.8 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1720140 Bytes = 1.6 MiB Load Address: 80008000 Entry Point: 80008000 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.0.8 (qin@ubuntu) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #13 Sat Jan 31 17:06:00 CST 2015 [ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: hi3518 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AXI bus clock 220000000. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 14224 [ 0.000000] Kernel command line: mem=56M console=ttyAMA0,115200 root=/dev/mtdblock3 rootfstype=squashfs rw init=/init mtdparts=hi_sfc:128k(u-boot)ro,64k(env),3072k(kernel),4608k(rootfs),512k(config),-(app) [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 56MB = 56MB total [ 0.000000] Memory: 52520k/52520k available, 4824k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xc4000000 - 0xfe000000 ( 928 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc3800000 ( 56 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .init : 0xc0008000 - 0xc0021000 ( 100 kB) [ 0.000000] .text : 0xc0021000 - 0xc0404000 (3980 kB) [ 0.000000] .data : 0xc0404000 - 0xc041d300 ( 101 kB) [ 0.000000] .bss : 0xc041d324 - 0xc042f660 ( 73 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:32 nr_irqs:32 32 [ 0.000000] sched_clock: 32 bits at 110MHz, resolution 9ns, wraps every 39045ms [ 0.000052] Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632) [ 0.070077] pid_max: default: 32768 minimum: 301 [ 0.070378] Mount-cache hash table entries: 512 [ 0.071492] CPU: Testing write buffer coherency: ok [ 0.075941] NET: Registered protocol family 16 [ 0.080455] Serial: AMBA PL011 UART driver [ 0.080778] uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2 [ 0.290221] console [ttyAMA0] enabled [ 0.294814] uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2 [ 0.302535] uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 25) is a PL011 rev2 [ 0.357156] bio: create slab at 0 [ 0.366134] SCSI subsystem initialized [ 0.373247] usbcore: registered new interface driver usbfs [ 0.379424] usbcore: registered new interface driver hub [ 0.385823] usbcore: registered new device driver usb [ 0.397212] cfg80211: Calling CRDA to update world regulatory domain [ 0.404316] Switching to clocksource timer1 [ 0.416560] NET: Registered protocol family 2 [ 0.421275] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.428909] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.436396] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.442969] TCP: Hash tables configured (established 2048 bind 2048) [ 0.449332] TCP reno registered [ 0.452534] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.458470] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.465423] NET: Registered protocol family 1 [ 0.470680] RPC: Registered named UNIX socket transport module. [ 0.476624] RPC: Registered udp transport module. [ 0.481411] RPC: Registered tcp transport module. [ 0.486126] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.538830] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.549605] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.558804] fuse init (API version 7.16) [ 0.565796] msgmni has been set to 102 [ 0.572909] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.580408] io scheduler noop registered [ 0.584347] io scheduler deadline registered (default) [ 0.589811] io scheduler cfq registered [ 0.625415] brd: module loaded [ 0.633034] Spi id table Version 1.22 [ 0.638265] Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18 [ 0.643734] SPI FLASH start_up_mode is 3 Bytes [ 0.648199] Spi(cs1): [ 0.650461] Block:64KB [ 0.652919] Chip:16MB [ 0.655280] Name:"MX25L128XX" [ 0.658434] spi size: 16MB [ 0.661179] chip num: 1 [ 0.663679] 6 cmdlinepart partitions found on MTD device hi_sfc [ 0.669605] Creating 6 MTD partitions on "hi_sfc": [ 0.674456] 0x000000000000-0x000000020000 : "u-boot" [ 0.683483] 0x000000020000-0x000000030000 : "env" [ 0.692212] 0x000000030000-0x000000330000 : "kernel" [ 0.701285] 0x000000330000-0x0000007b0000 : "rootfs" [ 0.710283] 0x0000007b0000-0x000000830000 : "config" [ 0.719340] 0x000000830000-0x000001000000 : "app" [ 0.744291] Fixed MDIO Bus: probed [ 1.115242] himii: probed [ 1.238153] usbcore: registered new interface driver zd1201 [ 1.243823] usbmon: debugfs is not available [ 1.248873] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.255880] hiusb-ehci hiusb-ehci.0: HIUSB EHCI [ 1.260615] hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1 [ 1.268540] hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000 [ 1.290122] hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00 [ 1.298294] hub 1-0:1.0: USB hub found [ 1.302203] hub 1-0:1.0: 1 port detected [ 1.307220] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.314420] hiusb-ohci hiusb-ohci.0: HIUSB OHCI [ 1.319049] hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2 [ 1.326797] hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000 [ 1.396371] hub 2-0:1.0: USB hub found [ 1.400298] hub 2-0:1.0: 1 port detected [ 1.412026] TCP cubic registered [ 1.415276] Initializing XFRM netlink socket [ 1.424836] NET: Registered protocol family 10 [ 1.432828] NET: Registered protocol family 17 [ 1.437400] NET: Registered protocol family 15 [ 1.442027] Registering the dns_resolver key type [ 1.452312] registered taskstats version 1 �[ 1.462516] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.469739] Freeing init memory: 100K _ _ _ _ _ _ _ _ _ _ _ _ \ _ _ _ _ _ ___ / /__/ \ |_/ / __ / - _ ___ / / / / / / _ _ _ _/ / / \_/ \_ ______ ___________\___\__________________ [RCS]: /etc/init.d/S00devs [RCS]: /etc/init.d/S01udev [ 3.580500] udevd (345): /proc/345/oom_adj is deprecated, please use /proc/345/oom_score_adj instead. [ 5.002416] ADDRCONF(NETDEV_UP): eth0: link is not ready ^vv^: tar -zxf /mnt/app/ipcam.tgz -C /home/bvtech ^vv^: decompress application package finished, start app. start load hi351x ko... import CHIPTYPE=hi3516c insmod mmz.ko mmz=anonymous,0,0x83800000,72M anony=1 insert audio [GetUsbExtDevMask:474]:ipcam detect dev mask is 0 [main:256]:sensor reset port:25, level:0 [detect_sensor_save:131]:we detect the sensor imx122 successfully rm: can't remove '/home/bvtech/lib/libsensor.so': No such file or directory gpio write:3 status:0 we detected wifi card [main:96]:reset serv start [GetUsbExtDevMask:474]:ipcam detect dev mask is 0x1 System startup success. Auto login as root ... Jan 1 00:00:22 login[648]: root login on 'ttyS000' Welcome to HiLinux. # [INFO.IPC_I8S_Constructor.3192][I8S]IPC_Constructor ! [INFO.IPC_I8S_Constructor.3202][I8S]IPC_Constructor ! [GetUsbExtDevMask:474]:ipcam detect dev mask is 0x1 [ipcam_sanity_check:79]:we detected system reboot abnormal last time [ipcam_check_init_func:635]:ipcam init encyptchip success! [ipcam_check_init_func:635]:ipcam init log success! [ipcam_check_init_func:635]:ipcam init usermng success! ip: RTNETLINK answers: Operation not supported [main:62]:exec [ip addr del dev eth0] resq[-1] ip: RTNETLINK answers: Operation not supported [main:62]:exec [ip addr del dev ra0] resq[-1] [main:62]:exec [rm -rf /tmp/wpa_supplicant*] resq[0] [main:62]:exec [wpa_supplicant -B -Dwext -i ra0 -c /etc/Wireless/wpa_supplicant.conf -P/tmp/wpa_supplicant-ra0.pid] resq[0] ip: RTNETLINK answers: Operation not supported [main:62]:exec [ip addr del dev ra0] resq[-1] udhcpc (v1.16.1) started Setting IP address 0.0.0.0 on ra0 Sending discover... No lease, forking to background [main:62]:exec [udhcpc -b -i ra0 -s /etc/dhcp/udhcpc.script -t 1 -A 2 -p /tmp/dhcp-ra0.pid] resq[0] [ipcam_check_init_func:635]:ipcam init network success! [rtc_get_time:73]:rtc time[19700102 00:49:47] [time_set_local:257]:changed systime from:1970-01-01 08:00:29 to 1970-01-02 00:49:47 [rtc_set_time:39]:rtc time[19700102 00:49:47] [ipcam_check_init_func:635]:ipcam init system time success! [ipcam_check_init_func:635]:ipcam init osd success! [ipcam_check_init_func:635]:ipcam init ftpserv success! ip: RTNETLINK answers: No such file or directory -------Sony IMX122 Sensor Initial OK!------- [MemMng_CalcMemSize:235]:memmng need total memery size:11315712 [HisiSmartAnalyzeInit:242]:init video smart analyze ok! [InitAvServer:324]:avserv init successfully with sns:1 [InitAvServVideo:29]:get mpeg codec para err, use default [HisiVencEnableChn:289]:chn:0 codec:0 width:1920 height:1080 profile:1 rc:0 fps:25 gop:50 bitrate:4000 quality:4 [HisiVencEnableChn:289]:chn:1 codec:0 width:352 height:288 profile:1 rc:0 fps:25 gop:50 bitrate:512 quality:4 [HisiVencEnableChn:289]:chn:2 codec:2 width:1920 height:1080 profile:1 rc:0 fps:1 gop:5 bitrate:1000 quality:4 [InitAvServAudio:77]:get audio para err, use default [ipcam_check_init_func:635]:ipcam init av serv success! [ipcam_check_init_func:635]:ipcam init protocol port success! [ipcam_check_init_func:635]:ipcam init ip filter success! [ipcam_check_init_func:635]:ipcam init disk serv success! [ipcam_check_init_func:635]:ipcam init email serv success! [ipcam_check_init_func:635]:ipcam init ftp client success! [ipcam_check_init_func:635]:ipcam init web serv success! [ipcam_check_init_func:635]:ipcam init ddns serv success! [ipcam_check_init_func:635]:ipcam init upnp serv success! [upnp_serv_device_start:174]:upnp serv success url:http://192.168.1.120:80/ [HisiVpssSetGrpParam:160]:vpass grp param level[1], agin[6387] [ipcam_check_init_func:635]:ipcam init rtsp serv success! [ipcam_check_init_func:635]:ipcam init rtmp serv success! [ipcam_check_init_func:635]:ipcam init record serv success! [ipcam_check_init_func:635]:ipcam init snap serv success! [RtspServWorkThr:109]:rtsp serv is running... [main:62]:exec [iconv -f utf-8 -t gb2312 /tmp/antsutf.ini>/tmp/antsgbk.ini] resq[0] [ipcam_check_init_func:635]:ipcam init ants serv success! local mac [d0 22 12 d1 c3 46] [I8S_DBG][I8S_SERVER_Initialize 1807]Server Initialized! [ipcam_check_init_func:635]:ipcam init ants i8s serv success! [ipcam_check_init_func:635]:ipcam init dana serv success! [ipcam_check_init_func:635]:ipcam init onvif serv success! [ipcam_check_init_func:635]:ipcam init bvcloud serv success! dbg_tail_start start Thread logtail_send succeeded dbg_tail_start start Thread logtail_send succeeded dbg_tail_startsearch_listen start Thread th_logtail_search_listen succeeded [HisiVpssSetGrpParam:160]:vpass grp param level[2], agin[10007] [ipcam_check_init_func:635]:ipcam init tcp serv success! [ipcam_check_init_func:635]:ipcam init schedule serv success! [ipcam_check_init_func:635]:ipcam init alarm serv success! [main:135]:ipcam main thread start. [danavideo_start_init:1153]:dana deviceid: [main:62]:exec [qrencode -o www/logo/qrcode.png] resq[0] === полная загрузка === login: root Password: ilovebv === dmesg === [ 0.000000] Linux version 3.0.8 (qin@ubuntu) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #13 Sat Jan 31 17:06:00 CST 2015 [ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: hi3518 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AXI bus clock 220000000. [ 0.000000] On node 0 totalpages: 14336 [ 0.000000] free_area_init_node: node 0, pgdat c041cc7c, node_mem_map c0430000 [ 0.000000] Normal zone: 112 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 14224 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 14224 [ 0.000000] Kernel command line: mem=56M console=ttyAMA0,115200 root=/dev/mtdblock3 rootfstype=squashfs rw init=/init mtdparts=hi_sfc:128k(u-boot)ro,64k(env),3072k(kernel),4608k(rootfs),512k(config),-(app) [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 56MB = 56MB total [ 0.000000] Memory: 52520k/52520k available, 4824k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xc4000000 - 0xfe000000 ( 928 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc3800000 ( 56 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .init : 0xc0008000 - 0xc0021000 ( 100 kB) [ 0.000000] .text : 0xc0021000 - 0xc0404000 (3980 kB) [ 0.000000] .data : 0xc0404000 - 0xc041d300 ( 101 kB) [ 0.000000] .bss : 0xc041d324 - 0xc042f660 ( 73 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:32 nr_irqs:32 32 [ 0.000000] sched_clock: 32 bits at 110MHz, resolution 9ns, wraps every 39045ms [ 0.000052] Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632) [ 0.070078] pid_max: default: 32768 minimum: 301 [ 0.070379] Mount-cache hash table entries: 512 [ 0.071493] CPU: Testing write buffer coherency: ok [ 0.075944] NET: Registered protocol family 16 [ 0.080463] Serial: AMBA PL011 UART driver [ 0.080786] uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2 [ 0.290231] console [ttyAMA0] enabled [ 0.294815] uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2 [ 0.302536] uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 25) is a PL011 rev2 [ 0.357180] bio: create slab at 0 [ 0.366171] SCSI subsystem initialized [ 0.373296] usbcore: registered new interface driver usbfs [ 0.379462] usbcore: registered new interface driver hub [ 0.385858] usbcore: registered new device driver usb [ 0.397228] cfg80211: Calling CRDA to update world regulatory domain [ 0.404327] Switching to clocksource timer1 [ 0.416580] NET: Registered protocol family 2 [ 0.421293] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.428926] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.436416] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.442991] TCP: Hash tables configured (established 2048 bind 2048) [ 0.449351] TCP reno registered [ 0.452553] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.458490] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.465441] NET: Registered protocol family 1 [ 0.470694] RPC: Registered named UNIX socket transport module. [ 0.476636] RPC: Registered udp transport module. [ 0.481423] RPC: Registered tcp transport module. [ 0.486139] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.538842] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.549614] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.558830] fuse init (API version 7.16) [ 0.565815] msgmni has been set to 102 [ 0.572935] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.580433] io scheduler noop registered [ 0.584371] io scheduler deadline registered (default) [ 0.589836] io scheduler cfq registered [ 0.625451] brd: module loaded [ 0.633042] Spi id table Version 1.22 [ 0.636726] Hisilicon Spi Flash Controller V350 Device Driver, Version 1.10 [ 0.638290] Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18 [ 0.643762] SPI FLASH start_up_mode is 3 Bytes [ 0.648228] Spi(cs1): [ 0.650486] Block:64KB [ 0.652946] Chip:16MB [ 0.655308] Name:"MX25L128XX" [ 0.658461] spi size: 16MB [ 0.661206] chip num: 1 [ 0.663706] 6 cmdlinepart partitions found on MTD device hi_sfc [ 0.669632] Creating 6 MTD partitions on "hi_sfc": [ 0.674485] 0x000000000000-0x000000020000 : "u-boot" [ 0.683503] 0x000000020000-0x000000030000 : "env" [ 0.692228] 0x000000030000-0x000000330000 : "kernel" [ 0.701310] 0x000000330000-0x0000007b0000 : "rootfs" [ 0.710303] 0x0000007b0000-0x000000830000 : "config" [ 0.719345] 0x000000830000-0x000001000000 : "app" [ 0.744305] Fixed MDIO Bus: probed [ 1.115244] himii: probed [ 1.238140] usbcore: registered new interface driver zd1201 [ 1.243809] usbmon: debugfs is not available [ 1.248858] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.255870] hiusb-ehci hiusb-ehci.0: HIUSB EHCI [ 1.260605] hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1 [ 1.268532] hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000 [ 1.290121] hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00 [ 1.298289] hub 1-0:1.0: USB hub found [ 1.302201] hub 1-0:1.0: 1 port detected [ 1.307223] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.314427] hiusb-ohci hiusb-ohci.0: HIUSB OHCI [ 1.319056] hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2 [ 1.326806] hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000 [ 1.396353] hub 2-0:1.0: USB hub found [ 1.400280] hub 2-0:1.0: 1 port detected [ 1.412010] TCP cubic registered [ 1.415261] Initializing XFRM netlink socket [ 1.424808] NET: Registered protocol family 10 [ 1.432802] NET: Registered protocol family 17 [ 1.437366] NET: Registered protocol family 15 [ 1.441985] Registering the dns_resolver key type [ 1.458791] registered taskstats version 1 [ 1.471096] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.478316] Freeing init memory: 100K [ 1.730213] mmc0: new SDHC card at address aaaa [ 1.950221] mmcblk0: mmc0:aaaa SS32G 29.7 GiB [ 2.079770] mmcblk0: p1 [ 4.011705] udevd (350): /proc/350/oom_adj is deprecated, please use /proc/350/oom_score_adj instead. [ 5.449405] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.311163] PHY: himii:01 - Link is Up - 100/Full [ 7.316066] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.310193] Hisilicon Media Memory Zone Manager [ 12.378873] hi3518_base: module license 'Proprietary' taints kernel. [ 12.378918] Disabling lock debugging due to kernel taint [ 12.390468] Hisilicon UMAP device driver interface: v3.00 [ 12.501453] pa:83800000, va:c4240000 [ 12.501493] load sys.ko for Hi3518...OK! [ 12.901890] load viu.ko for Hi3518...OK! [ 12.979750] ISP Mod init! [ 13.142835] load vpss.ko ....OK! [ 13.402042] load vou.ko ....OK! [ 13.608628] load venc.ko for Hi3518...OK! [ 13.699607] load group.ko for Hi3518...OK! [ 13.737269] load chnl.ko for Hi3518...OK! [ 13.861219] load h264e.ko for Hi3518...OK! [ 13.929996] load jpege.ko for Hi3518...OK! [ 14.074653] load rc.ko for Hi3518...OK! [ 14.151648] load region.ko ....OK! [ 14.241942] load vda.ko ....OK! [ 14.500956] hi_i2c init is ok! [ 14.589925] HiDog: set heartbeat to 0, heartbeat will not be changed. [ 14.589984] HiDog: default_margin value must be 0 [ 19.061964] usbcore: registered new interface driver rt2870 [ 24.622374] 0x1300 = 00064300 [ 35.350269] ra0: no IPv6 routers present === dmesg ===