=> reset
resetting ...
heartbeat = 1
=>NAak_fixed_clk_probe: parameters ok, nf=100 nr=1 nb=16 freq=400000000
pll2 frequency out: 400MHz
gclk frequency out: 200MHz


U-Boot 2019.10.0-V4.0.25-g970e72bc (Apr 11 2024 - 16:59:56 +0800)

CPU: 888MHz
Model: EVB_CBD_AK3918EV300L_V1.0.0 board
DRAM:  64 MiB
ak_fixed_clk_probe: parameters ok, nf=100 nr=1 nb=16 freq=400000000
ak_fixed_clk_probe pll2 has inited!
pll2 frequency out: 400MHz
gclk frequency out: 200MHz
Flash: SF: Detected XM25QH64C with page size 256 Bytes, erase size 4 KiB, total 8 MiB
8 MiB
MMC:   ak3918ev300l_gpio_probe
@get_card_status, card PLUGED
mmc1@20108000: 0
Loading Environment from SPI Flash... OK
In:    uart0@20130000
Out:   uart0@20130000
Err:   uart0@20130000
Net:   phy_id:0xffffffff
phy_id:0xffffffff
phy_id:0xffffffff
phy_id:0xffffffff
phy_id:0xffffffff
Could not get PHY for eth0: addr 1
ak_mac_probe, line:1956
eth-1: eth0@20300000

Hit CTRL+C to stop autoboot:  0
=> help
?         - alias for 'help'
base      - print or set address offset
bdinfo    - print Board Info structure
blkcache  - block cache diagnostics and control
bootm     - boot application image from memory
cmp       - memory compare
coninfo   - print console devices and information
cp        - memory copy
crc32     - checksum calculation
dcache    - enable or disable data cache
env       - environment handling commands
fatinfo   - print information about filesystem
fatload   - load binary file from a dos filesystem
fatls     - list files in a directory (default /)
fstype    - Look up a filesystem type
go        - start application at address 'addr'
help      - print command description/usage
icache    - enable or disable instruction cache
load      - load binary file from a filesystem
loadb     - load binary file over serial line (kermit mode)
loadx     - load binary file over serial line (xmodem mode)
loady     - load binary file over serial line (ymodem mode)
ls        - list files in a directory (default /)
md        - memory display
mm        - memory modify (auto-incrementing address)
mmc       - MMC sub system
mmcinfo   - display MMC info
mtdparts  - define flash/nand partitions
mw        - memory write (fill)
nm        - memory modify (constant address)
ping      - send ICMP ECHO_REQUEST to network host
printenv  - print environment variables
reset     - Perform RESET of the CPU
run       - run commands in an environment variable
saveenv   - save environment variables to persistent storage
setenv    - set environment variables
sf        - SPI flash sub-system
tftpboot  - boot image via network using TFTP protocol
version   - print monitor, compiler and linker version
=> printenv
a_uboot_flags=0x1
baudrate=115200
boot_normal=env set bootargs console=ttySAK0,115200n8 root=/dev/mtdblock5 rootfstype=squashfs init=/sbin/init ${mtdparts} ${mem} ${memsize}; run read_kernel; run read_dtb; bootm ${loadaddr} - ${fdtcontroladdr}
bootargs=console=ttySAK0,115200n8 root=/dev/mtdblock5 rootfstype=squashfs init=/sbin/init
bootargs_mode=0x0
bootcmd=run boot_normal
console=ttySAK0,115200n8
dtb_addr=0x0
dtb_name=DTB
dtb_offset=39000
dtb_size=db77
env_name=ENV
env_platform=anycloud3918ev300l_nor
env_version=1.0.01
envup_flags=1
ethaddr=<mac:3fd921ea2b3867f4>
fdt_high=0xFFFFFFFF
fdtcontroladdr=0x81300000
filesize=0x0
image_name=uImage
init=/sbin/init
ipaddr=192.168.1.99
kernel_addr=0x0
kernel_name=KERNEL
kernel_offset=49000
kernel_size=190000
loadaddr=0x80008000
logo_switch=0x0
mem=mem=64M
memsize=memsize=64M
mtd_root=/dev/mtdblock4
mtdparts=mtdparts=spi0.0:220K@0x0(UBOOT),4K@0x37000(ENV),4K@0x38000(ENVBK),64K@0x39000(DTB),1600K@0x49000(KERNEL),1100K@0x1D9000(ROOTFS),1000K@0x2EC000(EXT),800K@0x3E6000(JFFS2),2060K@0x4AE000(USR),1340K@0x6B1000(MVS),8192K@0x0(ALL)
netmask=255.255.255.0
part_table_offset=0x0
parttab_type=AK
read_dtb=sf probe 0:0 ${sf_hz} 0; sf read ${fdtcontroladdr} ${dtb_offset} ${dtb_size}
read_kernel=sf probe 0:0 ${sf_hz} 0; sf read ${loadaddr} ${kernel_offset} ${kernel_size}
root_name=ROOTFS
rootfstype=squashfs
sd_det_mode=0x0
serverip=192.168.1.1
setcmd=setenv bootargs console=${console} root=${mtd_root} rootfstype=${rootfstype} init=${init} mem=${memsize}
setgpio=0
sf_hz=20000000
stderr=uart0@20130000
stdin=uart0@20130000
stdout=uart0@20130000
uboot_name=UBOOT
update=tftp $(loadaddr) $(image_name); sf probe ; sf update $(loadaddr) $(update_offset) $(filesize)
update_flag=0x0
update_offset=0x0
update_size=0x0

Environment size: 1760/4092 bytes
=> version
U-Boot 2019.10.0-V4.0.25-g970e72bc (Apr 11 2024 - 16:59:56 +0800)

arm-anycloud-linux-uclibcgnueabi-gcc.br_real (Buildroot 2018.02.7_V1.0.05-g4b04ad0) 5.5.0
GNU ld (GNU Binutils) 2.29.1