U-Boot 2010.06 (Sep 28 2012 - 10:41:30) DRAM: 1 GiB MUXCTRL_REG19 1 GPIO3_3 WDT ON/OFF 1 SPI WRITE DEENBALE 1f0002 GPIO4_5 0 GPIO4_4 0 GPIO4_4 Relay ON/OFF NAND: Special Nand id table Version 1.23 Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 No NAND device found!!! 0 MiB Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18 Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128" In: serial Out: serial Err: serial user init finish. Hit any key to stop autoboot: 0 hisilicon # printenv bootcmd=sf probe 0;sf read 0x82000000 0x160000 0x340000;bootm 0x82000000 baudrate=115200 bootfile="uImage" bootdelay=1 bootargs=mem=92M console=ttyAMA0,115200 root=/dev/mtdblock6 rootfstype=jffs2 mtdparts=hi_sfc:256K(uboot),64K(ubenv),64K(ipenv),256K(env),768K(log),3328K(kernel),11648K(rootfs) mdio_intf=mii netmask=255.255.255.0 ethaddr= source=9 format=2 sdcard=1 ipaddr=192.168.0.62 serverip=192.168.0.2 stdin=serial stdout=serial stderr=serial verify=n ver=U-Boot 2010.06 (Sep 28 2012 - 10:41:30) Environment size: 519/65532 bytes hisilicon # help ? - alias for 'help' base - print or set address offset bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation getinfo - print hardware information go - start application at address 'addr' help - print command description/usage loadb - load binary file over serial line (kermit mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mtest - simple RAM read/write test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU saveenv - save environment variables to persistent storage setenv - set environment variables sf - SPI flash sub-system tftp - tftp - download or upload image via network using TFTP protocol version - print monitor version hisilicon # reset resetting ... U-Boot 2010.06 (Sep 28 2012 - 10:41:30) DRAM: 1 GiB MUXCTRL_REG19 1 GPIO3_3 WDT ON/OFF 1 SPI WRITE DEENBALE 1f0002 GPIO4_5 0 GPIO4_4 0 GPIO4_4 Relay ON/OFF NAND: Special Nand id table Version 1.23 Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 No NAND device found!!! 0 MiB Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18 Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128" In: serial Out: serial Err: serial user init finish. Hit any key to stop autoboot: 0 16384 KiB hi_sfc at 0:0 is now current device ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-2.6.35.7 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3117224 Bytes = 3 MiB Load Address: 80800000 Entry Point: 80800000 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.35.7 (jason@RD4Server) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.30.2+eabi+linuxpthread)) ) #3 Fri Sep 28 14:36:22 CST 2012 CPU: ARMv7 Processor [412fc098] revision 8 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: godeyes HIETH[hieth_mdio_intf_parse_tag] mdio_intf use:mii! Memory policy: ECC disabled, Data cache writeback l2cache_flush_all:l2cache_flag = 0,L2 cache may not enable! l2cache_flush_range:l2cache_flag = 0,L2 cache may not enable! l2cache_flush_range:l2cache_flag = 0,L2 cache may not enable! Built 1 zonelists in Zone order, mobility grouping on. Total pages: 23368 Kernel command line: mem=92M console=ttyAMA0,115200 root=/dev/mtdblock6 rootfstype=jffs2 mtdparts=hi_sfc:256K(uboot),64K(ubenv),64K(ipenv),256K(env),768K(log),3328K(kernel),11648K(rootfs) PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 92MB = 92MB total Memory: 87340k/87340k available, 6868k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xc6000000 - 0xe0000000 ( 416 MB) lowmem : 0xc0000000 - 0xc5c00000 ( 92 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0024000 ( 112 kB) .text : 0xc0024000 - 0xc0538000 (5200 kB) .data : 0xc0556000 - 0xc0582160 ( 177 kB) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:96 Console: colour dummy device 80x30 Calibrating delay loop... 878.18 BogoMIPS (lpj=4390912) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 L2cache cache controller enabled Serial: AMBA PL011 UART driver uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 46) is a AMBA/PL011 console [ttyAMA0] enabled uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 47) is a AMBA/PL011 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource timer1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Slow work thread pool: Starting up Slow work thread pool: Ready JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.14) SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 170 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler deadline registered (default) io scheduler cfq registered brd: module loaded loop: module loaded Spi id table Version 1.22 Hisilicon Spi Flash Controller V300 Device Driver, Version 1.10 Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18 Spi(cs1): Block:64KB Chip:16MB (Name:MX25L128) 7 cmdlinepart partitions found on MTD device hi_sfc Creating 7 MTD partitions on "hi_sfc": 0x000000000000-0x000000040000 : "uboot" 0x000000040000-0x000000050000 : "ubenv" 0x000000050000-0x000000060000 : "ipenv" 0x000000060000-0x0000000a0000 : "env" 0x0000000a0000-0x000000160000 : "log" 0x000000160000-0x0000004a0000 : "kernel" 0x0000004a0000-0x000001000000 : "rootfs" Special nand id table Version 1.33 Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10 Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 No NAND device found. Fixed MDIO Bus: probed hi_gmac_mii: probed PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver hiusb-ehci hiusb-ehci.0: HIUSB EHCI hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1 hiusb-ehci hiusb-ehci.0: irq 68, io mem 0x100b0000 hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver hiusb-ohci hiusb-ohci.0: HIUSB OHCI hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2 hiusb-ohci hiusb-ohci.0: irq 69, io mem 0x100a0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver ums-alauda usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-isd200 usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 mice: PS/2 mouse device common for all mice usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP cubic registered NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions ip6tnl0: Disabled Privacy Extensions NET: Registered protocol family 17 NET: Registered protocol family 15 lib80211: common routines for IEEE802.11 drivers VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2 registered taskstats version 1 usb 1-1: new high speed USB device using hiusb-ehci and address 2 VFS: Mounted root (jffs2 filesystem) on device 31:6. Freeing init memory: 112K [RCS]: /etc/init.d/S00devs mknod: /dev/ttyAMA0: File exists mknod: /dev/ttyAMA1: File exists mknod: /dev/ttyS000: File exists [RCS]: /etc/init.d/S01udev mkdir: can't create directory '/dev/pts': File exists [RCS]: /etc/init.d/S80network [RCS]: /etc/init.d/S99hunt report=1 Auto login as root ... Jan 1 00:00:11 login[636]: root login on 'ttyAMA0' Welcome to HiLinux. None of nfsroot found in cmdline. # insmod /hunt/ko/mmz.ko mmz=anonymous,0,0x85C00000,164M Hisilicon Media Memory Zone Manager hi3516_base: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Hisilicon UMAP device driver interface: v3.00 pa:85c00000, va:c61c0000 load sys.ko for Hi3516...OK! load h264e.ko ....OK! load mpeg4e.ko success. ISP Mod init! load vou.ko ....OK! load vpp.ko ....OK! load vda.ko ....OK! load rc.ko ....OK! load region.ko ....OK! load ive.ko ....OK! load tde.ko ....OK! hifb info: HIFB_MAIN_VERSION[HIFB_MAIN_VERSION] Build Time[Sep 21 2012, 09:28:59] hifb info: video:vram8_size:1658880 hifb info: succeed in registering the fb0: ovl8 frame buffer device gpio_i2c init is ok! acodec inited! Default:OLD MUXCTRL_REG27=1 Default:MUXCTRL_REG27=0 RTC/ADC_SCL:OLD MUXCTRL_REG70=1 RTC/ADC_SCL:MUXCTRL_REG70=0 RTC/ADC_SDA:OLD MUXCTRL_REG71=1 RTC/ADC_SDA:MUXCTRL_REG71=0 load_cmdline e_bootargs=mem=92M console=ttyAMA0,115200 root=/dev/mtdblock6 rootfstype=jffs2 mtdparts=hi_sfc:256K(uboot),64K(ubenv),64K(ipenv),256K(env),768K(log),3328K(kernel),11648K(rootfs) size=10000 baudrate=115200 bootfile="uImage" bootdelay=1 bootargs=mem=92M console=ttyAMA0,115200 root=/dev/mtdblock6 rootfstype=jffs2 mtdparts=hi_sfc:256K(uboot),64K(ubenv),64K(ipenv),256K(env),768K(log),3328K(kernel),11648K(rootfs) mdio_intf=mii netmask=255.255.255.0 ethaddr= source=9 format=2 sdcard=1 stdin=serial stdout=serial stderr=serial verify=n ver=U-Boot 2010.06 (Sep 28 2012 - 10:41:30) ipaddr=192.168.0.62 serverip=192.168.0.2 ReadIPENV IPENV_FILE_MAX=64 file_count=9 ReadIPENV(Config_env)>10 uboot env ok close(open_val) ++++++++Uboot_ENV OK++++++++++++++ ReadENV MTD_FILE_MAX=10 file_count=3 set i_input_source=9 board_type=3 camera_type=14 load_cmdline e_bootargs=mem=92M console=ttyAMA0,115200 root=/dev/mtdblock6 rootfstype=jffs2 mtdparts=hi_sfc:256K(uboot),64K(ubenv),64K(ipenv),256K(env),768K(log),3328K(kernel),11648K(rootfs) size=10000 baudrate=115200 bootfile="uImage" bootdelay=1 bootargs=mem=92M console=ttyAMA0,115200 root=/dev/mtdblock6 rootfstype=jffs2 mtdparts=hi_sfc:256K(uboot),64K(ubenv),64K(ipenv),256K(env),768K(log),3328K(kernel),11648K(rootfs) mdio_intf=mii netmask=255.255.255.0 ethaddr= source=9 format=2 sdcard=1 stdin=serial stdout=serial stderr=serial verify=n ver=U-Boot 2010.06 (Sep 28 2012 - 10:41:30) ipaddr=192.168.0.62 serverip=192.168.0.2 ReadIPENV IPENV_FILE_MAX=64 file_count=9 ReadIPENV(Config_env)>10 uboot env ok close(open_val) ++++++++Uboot_ENV OK++++++++++++++ Brand=x,CameraMode=x e_Ivs=0 source=9 e_board_version=0 e_aduio=1 e_ionum=11 e_icr=1 e_sdcard=1 speed_type=0 Wireless_Card=55 e_Other=0 e_zoom=0 e_IRIS=0 camera_type=INPUTTYPE_OV2715 check_value: 802.1x begin check_value: DSCP begin check_value: IPTABLE begin check_value: HTTPS begin check_value: SMTP begin check_value: smtp secure connect No USE: TLS default read value=8 reset sensor1=0 reset sensor2=0 reset sensor3=0 gpio=0 gpio1=0 gpio2=0 gpio3=0 Mode=1 Interval=10 Input1_PT=0 Input2_PT=0 Input3_PT=0 Input4_PT=0 rtusb init rt3070STA ---> === pAd = c6512000, size = 528648 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 usbcore: registered new interface driver rt3070STA (Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc] RTMP_TimerListAdd: add timer obj c655c930! RTMP_TimerListAdd: add timer obj c655c948! RTMP_TimerListAdd: add timer obj c655c960! RTMP_TimerListAdd: add timer obj c655c918! RTMP_TimerListAdd: add timer obj c655c8d0! RTMP_TimerListAdd: add timer obj c655c8e8! RTMP_TimerListAdd: add timer obj c6527364! RTMP_TimerListAdd: add timer obj c6513fa4! RTMP_TimerListAdd: add timer obj c6513fc4! RTMP_TimerListAdd: add timer obj c65273c0! RTMP_TimerListAdd: add timer obj c651679c! RTMP_TimerListAdd: add timer obj c651600c! RTMP_TimerListAdd: add timer obj c6516780! RTMP_TimerListAdd: add timer obj c6516a00! RTMP_TimerListAdd: add timer obj c6516818! RTMP_TimerListAdd: add timer obj c6516834! RTMP_TimerListAdd: add timer obj c65167b8! RTMP_TimerListAdd: add timer obj c65167d4! RTMP_TimerListAdd: add timer obj c65167f0! RTMP_TimerListAdd: add timer obj c6527334! RTMP_TimerListAdd: add timer obj c65273a4! -->RTUSBVenderReset <--RTUSBVenderReset Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 5 2. Phy Mode = 5 NVM is Efuse and its size =2d[2d0-2fc] ===WSC PBC HW trigger phy mode> Error! The chip does not support 5G band 5! RTMPSetPhyMode: channel is out of range, use first channel=1 (Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc] 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 MCS Set = ff 00 00 00 01 <==== rt28xx_init, Status=0 0x1300 = 00064300 ADDRCONF(NETDEV_UP): eth0: link is not ready No errors detected in compressed data of /html.zip. device_type=Device_09= read= ShowCameraMode=1 is_show=1 read= Brand=iZett Brand=iZett device_name= Device_09=HR-BT2030C device_name=HR-BT2030C Brand=iZett,device_name=HR-BT2030C is_show=1,Config_env->CameraType.e_CameraMode=x PHY: hi_gmac_mii:01 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready network_init: Wireless_Card=55 udhcpc (v1.16.1) started Sending discover... wlan_set_fix_ip: ifconfig eth1 0.0.0.0 Sending select for 192.168.0.23... Lease of 192.168.0.23 obtained, lease time 14400 deleting routers route: SIOCDELRT: No such process adding dns 192.168.0.1 shmdt(g_shmaddr) +++HLC_81CX_GPIO_INIT RTC/ADC_SCL:OLD MUXCTRL_REG70=0 RTC/ADC_SCL:MUXCTRL_REG70=0 RTC/ADC_SDA:OLD MUXCTRL_REG71=0 RTC/ADC_SDA:MUXCTRL_REG71=0 RTC is pcf8563. sec=53 version 1.1 ,isimx122=0 +++++==Onvif Discovery is start.==0 Jan 1 00:00:18 lld2d[974]: osl_write_pidfile: /var/run/lld2d-eth0.pid contains pid 975 which is still running; aborting IPCAM INIT OK Model_type=Model_09= is_show=1 Manufacturer=iZett udevice_name=HR-BT2030C RTC is pcf8563. rtc_time : 17:18:53 rtc_date : 2026-10-29 2026/10/29 17:18:53 1 RTC is pcf8563. rtc_time : 17:18:55 rtc_date : 2026-10-29 2026/10/29 17:18:55 1 Config_env->Read_eeprom.e_zoom=0 shmdt(g_shmaddr) load_cmdline e_bRTC is pcf8563. ootargs=mem=92M console=ttyAMA0,115200 root=/dev/mtdblock6 rootfstype=jffs2 mtdparts=hi_sfc:256K(uboot),64K(ubenv),64K(ipenv),256K(env),768K(log),3328K(kernel),11648K(rootfs) RTC 26/10/29 17:18:55 OV2715 sensor init success! 111111111111111enViDevType111111111111111=3 222222222222enViDevType111111111111111=3 ++++ SAMPLE_COMM_VI_StartDev OV_2715_DC_1080P ++++++ ::::::::::::::::::::::: Read Bs32Value:-5 ~u32AbsValue:-6 adPixelTable! ::::::::::::::::::::::: save BadPixelTable![Tue Jul 23 11:01:51 2013 ][file:/BadPixelTable] g_in_no=1 ,g_out_no=1 ===> Analyze_Cab_Info() CabInfo_buf===> "&start=71168&size=1025249" Start = 71168, Size = 1025249 ===> SetupActiveX_Cab() Cab_buf Write Create GPIOOutThreadLoop open dev=/dev/hgpioi2c fd=18 to read light sensor OK =ori lux= light_sensor_lux_show: ADC=0a Current_Lux=0 802.1x enable status:stop init... ok GetVideo0ThreadLoop PID=1005 h264 MODE 0 ::::::::::::::::::[ch:0]i_str=0;Resolution=8 GetVideo1ThreadLoop PID=1006 GetV3GPPThreadLoop PID=1007 GetAudioThreadLoop PID=1008 Change to G.711 Audio_Write_ThreadLoop PID=1009 AVI_RECORD_ThreadLoop PID=1010 Motion_SendMailThreadLoop PID=1011 OtherThreadLoop PID=1012 Other1ThreadLoop PID=1013 PingThreadLoop PID=1014 GPIOOutThreadLoop PID=1015 GPIOInThreadLoop PID=1016 Ddns_Send_ThreadLoop PID=1017 Schedule_ThreadLoop PID=1018 HttpdThreadLoop PID=1019 ERROR ReadDataMTD=/mtd/ptzname HTTPs set listen port=443 Width=1920 Height=1080 :::::::::::::::::::::Config_env->Video[0].i_Profile=2 >>>>>PT_H264>>>>>>VencChn=0;i_GOP=30;i_FPS=30 >>>>>stH264Cbr.fr32TargetFrmRate=30;u32ViFrmRate=30 >>>>>PT_H264>>>>>>stH264Cbr.u32BitRate[0]=4000 ::::::::::::::::::::::::::::::::::::::now=3;:::: :::::::::::::::::::::::::::::::::::::::stSrcChn.s32ChnId=3! Env->http_ssl.is_default=0 HTTPs init env_policy=HTTP_HTTPS_POLICY policy=HTTP_HTTPS_POLICY enable=stop HTTPs create CTX OK font_get(&unParam_load) HTTPs init with certificate check ok HTTPs cipher=DHE-RSA-AES256-SHA EDH-RSA-DES-CBC3-SHA DHE-RSA-AES128-SHA IDEA-CBC-SHA AES256-SHA DES-CBC3-SHA AES128-SHA EXP-DES-CBC-SHA init finish hrtsp_init HTTPs check request private key ok HTTPs init with request HTTPs set listen port=443 Env->http_ssl.is_default=0 HTTPs init env_policy=HTTP_HTTPS_POLICY policy=HTTP_HTTPS_POLICY enable=stop HTTPs create CTX OK HTTPs init with certificate check ok HTTPs cipher=DHE-RSA-AES256-SHA EDH-RSA-DES-CBC3-SHA DHE-RSA-AES128-SHA IDEA-CBC-SHA AES256-SHA DES-CBC3-SHA AES128-SHA EXP-DES-CBC-SHA init finish HTTPs check request private key ok HTTPs init with request hrtsp_init ok :::::::::::::::::::::::::[AveLum=0]:::[SP.strength=78]:::[SP.limit=78] >>>>Sharpness>>>>>>pstSharpenAttr.u32StrengthTarget=165 :::::::::::::Sharpness>>>>>>stSP_Ex.strength=69;b=0;w=255 >>[sfyStrength 0]>>tfyMaxStrength>>>>>=14;tfyLimit=42 >>>>pstDenoiseAttr.u8ThreshTarget>>>>>=15 ::::::::Contrast =50;Brightness=50;SatuVal=55;HueVal=49; :::::::::::::::::::pstAEAttr.u16DGainMin=1;Max=32;AGainMax=1 u32Strength=1;TargetpstDRCAttr.u32SlopeMax=4 ::::::::::::::::::::::WDR off::::::::::::::::::::: ::::::::::::pstAWBAttr.u8RGStrength=128 ::::::::::::pstAWBAttr.u8BGStrength=128 ::::::::::::pstAntiflicker.u8Frequency=0 ip_tables: (C) 2000-2006 Netfilter Core Team h264 MODE 1 ::::::::::::::::::[ch:1]i_str=2;Resolution=1 Width=640 Height=480 :::::::::::::::::::::Config_env->Video[1].i_Profile=0 >>>>>PT_H264>>>>>>VencChn=1;i_GOP=15;i_FPS=15 >>>>>stH264Cbr.fr32TargetFrmRate=15;u32ViFrmRate=30 >>>>>PT_H264>>>>>>stH264Cbr.u32BitRate[1]=512 mp4 MODE 2 GPIO0 Out=0x10 nf_conntrack version 0.5.0 (1366 buckets, 5464 max) **** change snmpd.conf **** set trap overrange snmp agent init... OK IOCTL::unknown IOCTL's cmd = 0x00008947 IOCTL::unknown IOCTL's cmd = 0x00008947 snmp agent start !!!!!!!!!!!!!!!in PWM_AE_DetThreadLoop !!!!!!!!!!!!!!!out PWM_AE_DetThreadLoop Mtd WriteFLOG file_count=95 reg=2508 killall: vo_hifb: no process killed enable_ICR: set day_night icr_enable:enable ::::::::Contrast =50;Brightness=50;SatuVal=0;HueVal=49; ICR_mechanism g_cmos_icr=1 bg_Color=fc1f fffffc1f fffffc1f fffffc1f fffffc1f bg_Color=8000 ffff8000 ffff8000 ffff8000 ffff8000 bg_Color=0 0 0 0 0 hifb info: The layer is show(1) now!