MP SPI-NOR Bootstrap v0.2 DDR Memory Size 128MB (1Gbx1) Boot image offset: 0x6000. Booting Image ..... 0567Will set the following freq... PLL1: 800 MHz, PLL2: 594 MHz, CPU freq: 594 MHz, AHB freq: 297 MHz, DDR freq: 800 MHz go... ********************************************* Please input ESC to run UBOOT Please input . to run burn-in Otherwise, system will run Linux after 1 sec ********************************************* Load image from SPI-NOR offset 0xa6000 to sdram 0x4000000 Jump 0x4000000 U-Boot 2008.10 (Jul 22 2011 - 15:37:46) DRAM: 128 MB Manufacturer ID : 0018 Device ID : 009F Device Code 2 : 0018 Flash: 0 kB #SF: Got idcode c2 20 18 ##In: serial Out: serial Err: serial Net: FTMAC110#0 Hit any key to stop autoboot: 0 #SF: Got idcode c2 20 18 16384 KiB MX25L12845E at 0:0 is now current device ################################################################################################################################### Booting kernel from Legacy Image at 02000000 ... Image Name: gm8126 Created: 2013-10-31 4:13:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 10113992 Bytes = 9.6 MB Load Address: 02000000 Entry Point: 02000040 Verifying Checksum ... OK XIP Kernel Image ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................................................................................................................................................................................................................................................................................ done, booting the kernel. Linux version 2.6.28 (boting_guo@RD4Server) (gcc version 4.4.0 (Faraday C/C++ Compiler Release 20100325) ) #12004 PREEMPT Thu Oct 31 12:12:58 CST 2013 CPU: FA626TE [66056261] revision 1 (ARMv5TE), cr=0000797f CPU: VIPT aliasing data cache, VIPT aliasing instruction cache Machine: Faraday GM8126 Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: mem=128M console=uart,shift,2,io,0xF9830000,38400 gmmem=74M Early serial console at I/O port 0xf9830000 (options '38400', shift 2) console [uart0] enabled PID hash table entries: 512 (order: 9, 2048 bytes) IC: Uknown!!!!!! 812622 GM Clock: CPU = 594 MHz, AHBCLK = 297 MHz, PLL1CLK = 800 MHz, PLL2CLK = 594 MHz ~UART_IER_MSI=0 <><6>console handover: boot [uart0] -> real [ttyS0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 117488KB available (3818K code, 357K data, 8080K init) Calibrating delay loop... 585.72 BogoMIPS (lpj=292864) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 688 bytes Fmem: node 0 is online, alloc pages = 18944(active pages = 32768) high_memory:0xc8000000, VM Start:0xc8800000, End:0xe0000000 NET: Registered protocol family 16 PMU: Mapped at 0xf9900000 pmu_get_cpu_clk:203 Attach GM AHB-DMA Driver SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 Video Timer(timer3) Max 28000ms in 0xf7d60b80 HZ. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 229 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered probe ftgpio010.0 OK!!, at c889c000 probe ftgpio010.1 OK!!, at c88a0000 probe ftgpio010.2 OK!!, at c88a4000 Serial: 8250/16550 driver 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xf9830000 (irq = 9) is a 16550A serial8250: ttyS1 at I/O 0xf9840000 (irq = 10) is a 16550A serial8250: ttyS3 at I/O 0xf9880000 (irq = 21) is a 16550A brd: module loaded loop: module loaded PPP generic driver version 2.4.2 NET: Registered protocol family 24 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky Linux video capture interface: v2.00 Creating 10 MTD partitions on "wb_spi_flash": 0x000d6000-0x00cc0000 : "Linux Section" 0x00cc0000-0x00d00000 : "User Section" 0x00001000-0x00006000 : "Loader Section" 0x00006000-0x000a6000 : "BurnIn Section" 0x000a6000-0x000d1000 : "UBoot Section" 0x000d2000-0x000d6000 : "Uboot Env" 0x00f00000-0x00f40000 : "Env Section" 0x00f40000-0x01000000 : "Log Section" 0x00d00000-0x00f00000 : "HTML Section" 0x000d1000-0x000d2000 : "IP Section" Probe FTSSP010 SPI Controller at 0x98200000 (irq 6) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver AMBA bus_register ok Enter Device A temp = 340 Drive Vbus because of ID pin shows Device A otg2xx device_register ok AMBA_bus_match(...) Found Driver FOTG2XX_DRV AMBA_bus_match(...) Found Driver FOTG2XX_DRV FOTG2XX_DRV fotg2xx_dev: GM USB2.0 Host Controller FOTG2XX_DRV fotg2xx_dev: new USB bus registered, assigned bus number 1 FOTG2XX_DRV fotg2xx_dev: irq 4, io mem 0xf9220000 FOTG2XX_DRV fotg2xx_dev: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected FOTG200 Controller Initialization fotg200 int enable = 1f30 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems i2c /dev entries driver ftiic010 ftiic010.0: irq 18, mapped at c88b0000 Advanced Linux Sound Architecture Driver Version 1.0.18rc3. ALSA device list: No soundcards found. TCP cubic registered NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions ip6tnl0: Disabled Privacy Extensions NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. Freeing init memory: 8080K Warning: unable to open an initial console. FTMAC with FARADAY Internal PHY support FTMAC110 Driver (Linux 2.6) 01/10/11 - (C) 2011 GM Corp. reset Faraday Internal PHY. <><><>~UART_IER_MSI=a <>probe cpu: C ver. cpu_id=81262220(GM8125_ID) ret=1 load_cmdline e_bootargs=mem=128M console=uart,shift,2,io,0xF9830000,38400 gmmem=74M size=4000 baudrate=38400 netmask=255.255.255.0 ethact=FTMAC110#0 ethaddr= source=119 format=2 sdcard=1 serveriInit SAR ADC done. p=192.168.0.2 ipaddr=192.168.0.62 bootargs=mem=128M console=uart,shift,2,io,0xF9830000,38400 gmmem=register sar adc device (0) OK!! 74M bootdelay=1 ver=U-Boot 2008.10 (Jul 22 2011 - 15:37:46) ReadIPENV IPENV_FILE_MAX=32 file_count=5 ReadIPENV(Config_env)>10 uboot env ok close(open_val) ++++++++Uboot_ENV OK++++++++++++++ ReadENV MTD_FILE_MAX=9 file_count=6 set i_input_source=119 board_type=9 camera_type=6 load_cmdline e_bootargs=mem=128M console=uart,shift,2,io,0xF9830000,38400 gmmem=74M size=4000 baudrate=38400 netmask=255.255.255.0 ethact=FTMAC110#0 ethaddr= source=119 format=2 sdcard=1 serverip=192.168.0.2 ipaddr=192.168.0.62 bootargs=mem=128M console=uart,shift,2,io,0xF9830000,38400 gmmem=74M bootdelay=1 ver=U-Boot 2008.10 (Jul 22 2011 - 15:37:46) ReadIPENV IPENV_FILE_MAX=32 file_count=5 ReadIPENV(Config_env)>10 uboot env ok close(open_val) ++++++++Uboot_ENV OK++++++++++++++ Brand=x,CameraMode=x e_Ivs=0 source=119 e_board_version=0 e_aduio=1 e_ionum=11 e_icr=0 e_sdcard=1 speed_type=0 Wireless_Card=55 e_Other=0 e_model=0 vol_mic=8 board_type=BOARD_840_V0 camera_type=INPUTTYPE_7720 check_value: 802.1x begin check_value: DSCP begin check_value: IPTABLE begin check_value: HTTPS begin check_value: SMTP begin check_value: smtp secure connect No USE: TLS adc0_read: dev=/dev/ftsar_adc010_0_key read SW1 to detect factory default IPCAM gm812x version=VB1.0.42_SO rt5370sta: module license 'unspecified' taints kernel. rtusb init rt3070STA ---> usbcore: registered new interface driver rt3070STA ftrtc011 ftrtc011: rtc core: registered ftrtc011 as rtc0 rm /hunt/dac5571/dac5571.ko Mounting user MTD partion Has JFFS2 on mtdblock1 mmc0: SDHCI controller on [ftsdc010] using DMA adjust high memory size=0x24(36)MB Frammap: 9728 pages in DDR0 are freed. Frammap: DDR0: memory base=0x1800000, memory size=0x2400000, alignment=256K Frammap: version 0.28.3, 1 DDR is managed. VideoGraph v0.44 You may use #echo 11 > /proc/videograph/dbg to enable debug mode (0xbf16550c) Debug message at 0xc8a48000 start pointer 0xbf1855f0 size 0x124f80 Insert dvr_common driver done. Platform GM812600 enc_in0=(buf: 614400,4,0) enc_in0_d=(buf: 614400,4,1) enc_out0=(res: 640,480) enc_out0=(buf: 307200,3,0) scl0_out0=(res: 320,240) scl0_out0=(buf: 153600,3,0) scl1_out0=(res: 176,144) scl1_out0=(buf: 50688,2,0) ssenc_out0=(buf: 307200,1,0) sub1_enc_out0=(res: 640,480) sub1_enc_out0=(buf: 307200,3,0) enc_in1=(buf: 614400,4,0) enc_in1_d=(buf: 614400,4,1) enc_out1=(res: 640,480) enc_out1=(buf: 307200,3,0) scl0_out1=(res: 320,240) scl0_out1=(buf: 153600,3,0) scl1_out1=(res: 176,144) scl1_out1=(buf: 50688,2,0) ssenc_out1=(buf: 307200,1,0) sub1_enc_out1=(res: 640,480) sub1_enc_out1=(buf: 307200,3,0) enc_in3=(buf: 153600,4,0) enc_in3_d=(buf: 153600,4,1) enc_out3=(res: 320,240) enc_out3=(buf: 76800,3,0) scl0_out3=(res: 176,144) scl0_out3=(buf: 50688,2,0) ssenc_out3=(buf: 76800,1,0) sub1_enc_out3=(res: 320,240) sub1_enc_out3=(buf: 153600,2,0) sub2_enc_out3=(res: 176,144) sub2_enc_out3=(buf: 25344,2,0) fcap: V0.3.12 vcap_dev: [0]:bAlbum_bug=0, bCrop_bug=1, bCU_bug=0 LL_BusDeadlock_bug=0, bSupportSplitOSDDispRamWritePort=1 fcap: [0]: Link List mode! fcap: fosd00: minor=57 fcap: fosd02: minor=56 fcap: fosd01: minor=55 fcap: fosd03: minor=54 vcap_dev: [1]:bAlbum_bug=0, bCrop_bug=1, bCU_bug=0 LL_BusDeadlock_bug=0, bSupportSplitOSDDispRamWritePort=1 fcap: [1]: Link List mode! fcap: fosd10: minor=53 fcap: fosd12: minor=52 fcap: fosd11: minor=51 fcap: fosd13: minor=50 insmod /lib/modules/fcap200_ov7720.ko probe ov7720 i2c OK. GPIO-50 autorequested input_init: ov7725 pulse(500ms) reset_pin=cap1_18 OV7720: Set I2C Command OK SCL: Version, v1.13 SCL: div:4 replace favc driver for new_cpu mcp200 pmu register FAVC Encoder IRQ mode(29)v4.2.1 FAVC codec Max Resolution is 640x480, built @ May 10 2012 16:20:46 MCP100 driver with CPU for VG GM8126 MPEG4 with CPU for VG, decoder ver: 3.2.2, encoder ver: 3.2.6 GM8126 MJPEG with CPU for VG, encoder ver: 3.2.4, decoder ver: 3.1.4 FTDI210 registers 32 entities to video graph! FTDI210 Driver v1.4 (1 engine(s)) ft-32ssp: common[ver:0.3.4] INIT OK! card->cardno = 2 card->pbase = 98a00000 card->vbase = c8de0000 card->irq = 11 my_card->capture.dma_ch = 4 my_card->playback.dma_ch = 5 ft-32ssp: SoundCard(2) attached OK (c3d645d0) I2S probe ok in Slave mode. MPFX: Register PWM character driver success! GPIO driver func=53 register finish vsrc_number=0, max_frame_rate=30 devmem 0x99000038 32 0xf87ea2a3 autoframe_map : 1 autoframe_map : 3 turn on ch[0] ch[1] auto frame rate ADDR: ftmac110_link_change:2113 ftmac110_link_change:2127 Not word aligned WriteDataMTD=/html.zip DataSize=1776293,reg=1776293 load www finish device_type=Device_77= read=ShowCameraMode=1 is_show=1 read=Brand=iZett Brand=iZett device_name=Device_77=HR-CB6430B device_name=HR-CB6430B Brand=iZett,device_name=HR-CB6430B is_show=1,Config_env->CameraType.e_CameraMode=x ==================Enter copy_file================== =================================================== ==================Enter copy_file================== =================================================== usbcore: deregistering interface driver rt3070STA <--- rtusb exit ralink_wifi_unload_module: not found Ranlink wifi module udhcpc (v1.13.4) started set_net_led: on=1 data=0 Sending discover... Sending select for 192.168.0.61... Lease of 192.168.0.61 obtained, lease time 14400 +++++==Onvif Discovery is start.==0 deleting routers adding dns 192.168.0.1 shmdt(g_shmaddr) IPCAM INIT OK Model_type=Model_77= is_show=1 Manufacturer=iZett udevice_name=HR-CB6430B RTC_READ_TIME: 2026/10/27 12:29:07 2 run hunt_server shmdt(g_shmaddr) 2026/10/27 12:29:08 / # Options error: In [CMD-LINE]:1: Error opening configuration file: /www/keys/client.conf Use --help for more information. g_in_no=1 ,g_out_no=1 get cpu: C ver. cpu_id=81262220(GM8125_ID) ret=1 !!!!!!!AAAAAA light_lux_level ===> Anfcap: [1]:OSD P0 default fonts num=42 alyfcap: [1]:OSD P1 default fonts num=42 ze_Cab_Ifcap: [0]:OSD P0 default fonts num=42 nfofcap: [0]:OSD P1 default fonts num=42 () CabInfo_buf===> "&start=71168&size=1024899" Start = 71168, Size = 1024899 ===> SetupActiveX_Cab() Cab_buf Write open dev=/dev/ftpwmtmr010 fd=4 OK pwm_start: pwm[1] OK pwm_set_para: pwm[1] set freq=15400 OK pwm_set_para: pwm[1] se tvsrc_number=0, max_frame_rate=30 duty=10 OK Set_OV7720: set PAL video system open OSD CH3 open OSD CH1 open OSD CH0 GetAudioThreadLoop PID=839 aac_init: <1> aac_bitrate=UNKNOWN bit new bitrate=0 Audio_Write_ThreadLoop PID=839 Audio Change to G.711 AVI_RECORD_ThreadLoop PID=839 Motion_SendMailThreadLoop PID=839 OtherThreadLoop PID=839 Other1ThreadLoop PID=839 PingThreadLoop PID=839 GPIOOutThreadLoop PID=839 Create GPIOOutThreadLoop GPIOInThreadLoop PID=839 Ddns_Send_ThreadLoop PID=839 Schedule_ThreadLoop PID=839 HttpdThreadLoop PID=839 ERROR ReadDataMTD=/mtd/ptzname 802.1x enable status:stop init... ok HTTPs set listen port=443 Env->http_ssl.is_default=0 HTTPs init env_policy=HTTP_HTTPS_POLICY policy=HTTP_HTTPS_POLICY enable=stop HTTPs create CTX OK HTTPs init with certificate check ok HTTPs cipher=RC4-MD5 init finish HTTPs check request private key ok HTTPs init with request ip_tables: (C) 2000-2006 Netfilter Core Team MP4 rate control version: fix 0.95 resolution=640x480 Platform 8126 version 81262220 refcap: [0]:IN=OV7720 solutallocate luma qtabl = c117d000 ifake luma qtabl = 0 on=640x480 video0: stream0__main =============================================================================== set_main_parameter: video[0] ntsc mpeg4 fps=30 bps=1000Kb tps=1000Kb gop=30 640x480 ECBR q(max=31 min=6 init=10) qty=0 =============================================================================== set threshold 30 (dataout_0) Timeout to wait AP buffer get, skip! (0xa20d,0xa2e5 flow 198) ##### Transfer Group 0 Done,399ms! GPIO0out0=0x1 (dataout_0) Timeout to wait AP buffer get, skip! (0xa2fe,0xa3da flow 198) (dataout_0) Timeout to wait AP buffer get, skip! (0xa3fd,0xa4c7 flow 198) ENC_OFFSET_QP = 8 chn 0: intra_qp_offset: 8 -> 8 allocate luma qtabl = c7c09000 fake luma qtabl = 0 video1: stream1__main =============================================================================== set_main_parameter: video[(dataout_0) Timeout to wait AP buffer get, skip! (0xa4e3,0xa5b2 flow 198) 1] ntsc mpeg4 fps=10 bps=512Kb tps=512Kb gop=30 640x480 Eset threshold 30 CBR q(max=31 min=6 init=10) qty=0 =============================================================================== ENC_OFFSET_QP = 8 chn 1: intra_qp_offset: 0 -> 8 (dataout_0) Timeout to wait AP buffer get, skip! (0xa5cf,0xa6a5 flow 198) H264 rate control version: fix 0.95 video2: stream3__main =============================================================================== set_main_parameter: video[2] ntsc h264 fps=5 bps=0Kb tps=750Kb gop=5 320x240 EVBR q(max=51 min=30 init=30) qty=0 =============================================================================== (dataout_1) Timeout to wait AP buffer get, skip! (0xa61e,0xa761 flow 300) ##### Transfer Group 1 Done,489ms! Platform 8126 version 81262220 fcap: [1]:IN=OV7720 allocate luma qtabl = c119f000 fake luma qtabl = 0 (dataout_0) Timeout to wait AP buffer get, skip! (0xa6c2,0xa7b1 flow 198) video3: stream3__sub1 =============================================================================== set_sub_parameter: video[3] yuv422 fps=5 bps=0Kb tps=750Kb gop=5 320x240 EVBR q(max=51 min=35 init=35) qty=0 =============================================================================== (dataout_0) Timeout to wait AP buffer get, skip! (0xa7d0,0xa89d flow 198) (dataout_1) Timeout to wait AP buffer get, skip! (0xa78f,0xa8d0 flow 300) (dataout_0) Timeout to wait AP buffer get, skip! (0xa8ba,0xa987 flow 198) ##### Transfer Group 2 Done,505ms! video3: stream3__sub2 =============================================================================== set_sub_parameter: video[3] mpeg4 fps=5 bps=64Kb tps=64Kb gop=5 176x144 ECBR q(max=31 min=6 init=10) qty=0 =============================================================================== ##### Transfer Group 2 Done,753ms! hrtsp_init start hrtsp_init ok Set_OV7720: set PAL video system nf_conntrack version 0.5.0 (2048 buckets, 8192 max) ##### Transfer Group 2 Done,760ms! snapshot_get_frame: ch=3 timeout **** change snmpd.conf **** set trap overrange snmp agent init... OK snmp agent start wdt keepalive time is 5 sec. total used free shared buffers Mem: 125716 74020 51696 0 0 Swap: 0 0 0 Total: 125716 74020 51696 set_net_led: on=1 data=0 Mtd WriteFLOG file_count=73 reg=2508 rm /hunt/ipcam / #