IPL g8e04b60 D-1f HW Reset miupll_233MHz MIU0 zq=0x003c miu_bw_set utmi_1_init done utmi_2_init done utmi_3_init done usbpll init done...... SPI 54M clk_init done P1 USB_rterm trim=0x0000 P1 USB_HS_TX_CURRENT trim=0x0001 P2 USB_rterm trim=0x0000 P2 USB_HS_TX_CURRENT trim=0x0001 P3 USB_rterm trim=0x0000 P3 USB_HS_TX_CURRENT trim=0x0001 PM_vol_bgap trim=0x0000 GCR_SAR_DATA trim=0x0195 ETH 10T output swing trim=0x0000 ETH 100T output swing trim=0x0010 ETH RX input impedance trim=0x0000 ETH TX output impedance trim=0x0000 MIPI_HS_RTERM trim=0x0001 MIPI_LP_RTERM trim=0x0000 TX_current trimming trim[0x1A]=0x0046 TX_current trimming trim[0x1B]=0x0047 TX_current trimming trim[0x1C]=0x0046 HDMI2TX Rterm trim=0x0001 HDMI2TX_Ibias_CH0 trim=0x001a HDMI2TX_Ibias_CH1 trim=0x001a HDMI2TX_Ibias_CH2 trim=0x001b HDMI2TX_Ibias_CH3 trim=0x001a 256MB BIST0_0001-OK Enable MMU and CACHE Load IPL_CUST from NOR offset:00010000 Unable to detect NOR Load time 682 us, 25900 KiB/s crc OK IPL_CUST g8e04b60 MXP found at 0x00020000 runUBOOT() runUBOOT() [SPI_NOR] -Verify UBOOT CRC32 passed! -Decompress UBOOT XZ decomp_size=0x00081748 Disable MMU and D-cache before jump to UBOOTę U-Boot 2015.01 (Jul 08 2021 - 13:47:28) Version: I2g7a7d1f9 I2C: ready DRAM: WARNING: Caches not enabled gpio debug MHal_GPIO_Pad_Set: pin=44 gpio debug MHal_GPIO_Pad_Set: pin=17 gpio debug MHal_GPIO_Pad_Set: pin=18 gpio debug MHal_GPIO_Pad_Set: pin=39 nor_flash_mxp allocated success!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Unknown flash type (0x20, 0x40, 0x18) and use default flash type please add flash info to serial flash driver !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! SF: Detected nor0 with total size 16 MiB MXP found at mxp_offset[3]=0x00020000, size=0x1000 env_offset=0x60000 env_size=0x10000 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Unknown flash type (0x20, 0x40, 0x18) and use default flash type please add flash info to serial flash driver !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! SF: Detected nor0 with total size 16 MiB In: serial Out: serial Err: serial Net: MAC Address Auto-Negotiation... AN failLink Status Speed:10 Full-duplex:0 Status Error! sstar_emac Hit any key to stop autoboot: 0 SigmaStar # help ? - alias for 'help' aes - Control Mstar AES engine base - print or set address offset bootlogo- show bootlogo bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bzr - bzr - buzzer sound out. cmp - memory compare cp - memory copy crc32 - checksum calculation dbg - set debug message level. Default level is INFO dcache - enable or disable data cache debug - Disable uart rx via PAD_DDCA to use debug tool env - environment handling commands estar - script via network estart - EMAC start fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fatsize - determine a file's size go - start application at address 'addr' gpio - Config gpio port help - print command description/usage i2c - I2C sub-system icache - enable or disable instruction cache initDbgLevel- Initial varaible 'dbgLevel' loop - infinite loop on address range macaddr - setup EMAC MAC addr md - memory display mm - memory modify (auto-incrementing address) mw - memory write (fill) mxp - MXP function for Mstar MXP partition nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables reset - Perform RESET of the CPU riu - riu - riu command run - run commands in an environment variable saveenv - save environment variables to persistent storage secauth - Control Sstar security authenticate sequence setenv - set environment variables sf - SPI flash sub-system sfbin - for uploading sf image to a server(via network using TFTP protocol) srcfg - sensor pin and mclk configuration. tftpboot- boot image via network using TFTP protocol uart - UART sub-system usb - USB sub-system usbboot - boot from USB device usbstar - script via USB package ustar - script via USB version - print monitor, compiler and linker version SigmaStar # printenv baudrate=115200 bootargs=console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=squashfs ro init=/linuxrc LX_MEM=0xff00000 mma_heap=MMU_MMA,miu=0,sz=0x3800000 mma_heap=mma_heap_name0,miu=0,sz=0x3C00000 mma_memblock_remove=1 bootcmd=${s10};${s11};${s12};${s13}; bootdelay=0 cpu_part_start=1425e000 ethact=sstar_emac ethaddr= fileaddr=235cc190 filesize=143 ipaddr=192.168.1.114 netmask=255.255.0.0 s10=bootlogo s11=sf probe 0 s12=sf read 0x22000000 0x70000 0x280000 s13=bootm 0x22000000 s21=bzr 200 1 s22=bzr 55 1 s23=usb start 2 s24=fatload usb 0 0x22000000 help.rom s41=bzr 55 2 s42=bzr 500 1 s43=bzr 500 4 s44=reset serverip=192.168.1.1 sf_kernel_size=280000 sf_kernel_start=70000 sf_part_size=40000 sf_part_start=ef0000 stderr=serial stdin=serial stdout=serial usb_folder=images Environment size: 860/4092 bytes SigmaStar # version U-Boot 2015.01 (Jul 08 2021 - 13:47:28) arm-buildroot-linux-uclibcgnueabihf-gcc.br_real (Buildroot 2017.08-gc7bbae9-dirty) 4.9.4 GNU ld (GNU Binutils) 2.28.1 SigmaStar #