System startup Uncompress.........Ok System startup U-Boot 2010.06-dirty (Dec 25 2022 - 21:23:28) Check Flash Memory Controller v100 ... Found SPI Nor(cs 0) ID: 0xc8 0x40 0x18 Block:64KB Chip:16MB Name:"GD25Q128" SPI Nor total size: 16MB Cannot found a valid SPI Nand Device MMC: EMMC/MMC/SD controller initialization. Card did not respond to voltage select! No EMMC/MMC/SD device found ! In: serial Out: serial Err: serial RAM size: 64MB *No SD card found! USB: scanning bus for devices... 1 USB Device(s) found 0 Storage Device(s) found Hit any key to stop autoboot: 0 OpenIPC # OpenIPC # help ? - alias for 'help' base - print or set address offset bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootss - boot from snapshot image cmp - memory compare cp - memory copy crc32 - checksum calculation ddr - ddr training function exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) false - do nothing, unsuccessfully fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) getinfo - print hardware information go - start application at address 'addr' help - print command description/usage loadb - load binary file over serial line (kermit mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - mmcinfo -- display MMC info mtest - simple RAM read/write test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables sf - SPI flash sub-system showvar - print local hushshell variables test - minimal test like /bin/sh tftp - tftp - download or upload image via network using TFTP protocol tftpboot- tftpboot - download or upload image via network using TFTP protocol true - do nothing, successfully usb - USB sub-system usbboot - boot from USB device version - print monitor version OpenIPC # printenv bootargs=mem=${osmem} console=ttyAMA0,115200 panic=20 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdp} bootcmd=setenv setargs setenv bootargs ${bootargs}; run setargs; sf probe 0; sf read ${baseaddr} 0x50000 0x30t bootdelay=1 baudrate=115200 ipaddr=192.168.1.10 serverip=192.168.1.254 gatewayip=192.168.1.1 netmask=255.255.255.0 bootfile="uImage" baseaddr=0x82000000 uknor8m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} uImage.${soc} && sf probe 0; sf erase 0x50000 0x200} uknor16m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} uImage.${soc} && sf probe 0; sf erase 0x50000 0x30} urnor8m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} rootfs.squashfs.${soc} && sf probe 0; sf erase 0x25} urnor16m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} rootfs.squashfs.${soc} && sf probe 0; sf erase 0x3} uknand=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} uImage.${soc} && nand erase 0x100000 0x300000; nand 0 urnand=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} rootfs.ubi.${soc} && nand erase 0x400000 0x7c00000; } mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data) mtdpartsubi=setenv mtdparts hinand:256k(boot),768k(wtf),3072k(kernel),-(ubi) mtdpartsnand=setenv mtdparts hinand:256k(boot),768k(wtf),3072k(kernel),10240k(rootfs),-(rootfs_data) mtdpartsnor8m=setenv mtdparts hi_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data) mtdpartsnor16m=setenv mtdparts hi_sfc:256k(boot),64k(env),3072k(kernel),10240k(rootfs),-(rootfs_data) nfsroot=/srv/nfs/hi3518ev200 bootargsnfs=mem=${osmem} console=ttyAMA0,115200 panic=20 root=/dev/nfs rootfstype=nfs ip=${ipaddr}:::255.255.} bootargsubi=mem=${osmem} console=ttyAMA0,115200 panic=20 init=/init root=ubi0:rootfs rootfstype=ubifs ubi.mtd} bootnfs=setenv setargs setenv bootargs ${bootargsnfs}; run setargs; tftpboot ${baseaddr} uImage.${soc}; bootm} bootcmdnand=setenv setargs setenv bootargs ${bootargs}; run setargs; nand read ${baseaddr} 0x100000 0x300000;} bootcmdubi=setenv setargs setenv bootargs ${bootargsubi}; run setargs; nand read ${baseaddr} 0x100000 0x30000} bootcmdnor=setenv setargs setenv bootargs ${bootargs}; run setargs; sf probe 0; sf read ${baseaddr} 0x50000 0} setnand=run mtdpartsubi; setenv bootcmd ${bootcmdubi}; saveenv; reset setnor8m=run mtdpartsnor8m; setenv bootcmd ${bootcmdnor}; saveenv; reset setnor16m=run mtdpartsnor16m; setenv bootcmd ${bootcmdnor}; saveenv; reset restore=n osmem=32M soc=hi3518ev200 =664affac wlandev=rtl8188eu-hi3518ev200-qvc-ipc-136w extras=initcall_blacklist=hisi_femac_driver_init board=hs303-v3 sensor=ov9732 wlanssid=############ wlanpass=########## ethaddr=##:##:##:##:##:## upgrade=https://github.com/OpenIPC/builder/releases/download/latest/hi3518ev200_lite_qtech-qvc-ipc-136w-nor.tz stdin=serial stdout=serial stderr=serial totalmem=64M verify=n ver=U-Boot 2010.06-dirty (Dec 25 2022 - 21:23:28) Environment size: 3377/65532 bytes OpenIPC # version U-Boot 2010.06-dirty (Dec 25 2022 - 21:23:28) OpenIPC #