U-Boot 2013.10.0-AK_V3.0.05 (Aug 10 2020 - 03:27:13) DRAM: 64 MiB 8 MiB Create flash partition table init OK! ak_sdhsmmc_init: ANYKA SDHC/MMC4.0: 0 Load Env CRC OK! In: serial Out: serial Err: serial reset pin value: 1 Hit any key to stop autoboot: 1  0 SF: 1420448 bytes @ 0x39000 Read: OK ## Booting kernel from Legacy Image at 81b08000 ... Image Name: Linux-3.4.35 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1420384 Bytes = 1.4 MiB Load Address: 81b08000 Entry Point: 81b08040 Verifying Checksum ... OK XIP Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Anyka Linux Kernel Version: 1.1.12 Booting Linux on physical CPU 0 Linux version 3.4.35 (caibin@apemans_server) (gcc version 4.8.5 (anyka (gcc-4.8.5 + binutils-2.24 + ulcibc-0.9.33.2)(20170223)) ) #1 Wed Aug 19 06:47:45 UTC 2020 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: CLOUD39EV3_AK3918EV300_MNBD Memory policy: ECC disabled, Data cache writeback ANYKA CPU AK3918 (ID ) Built 1 zonelists in Zone order, mobility grouping on. Total pages: 9398 Kernel command line: console=ttySAK0,115200n8 root=/dev/mtdblock4 rootfstype=squashfs init=/sbin/init mem=64M memsize=64M PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 37MB = 37MB total Memory: 33276k/33276k available, 4612k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc2800000 - 0xff000000 ( 968 MB) lowmem : 0xc0000000 - 0xc2500000 ( 37 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc03a8000 (3712 kB) .init : 0xc03a8000 - 0xc03c3000 ( 108 kB) .data : 0xc03c4000 - 0xc03e9f38 ( 152 kB) .bss : 0xc03e9f5c - 0xc040aec8 ( 132 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:117 sched_clock: 32 bits at 12MHz, resolution 83ns, wraps every 357913ms AK39 console driver initial console [ttySAK0] enabled Calibrating delay loop... 199.06 BogoMIPS (lpj=995328) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0x81ddbf60 - 0x81ddbfb8 devtmpfs: initialized NET: Registered protocol family 16 On-chip L2 memory initialized AK39 clocks: CPU 400MHz, MEM 400MHz, ASIC 120MHz Anyka platform share gpio locks initialize. bio: create slab at 0 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb i2c-ak39 i2c-ak39: Unable to achieve desired frequency 300KHz. Lowest achievable 312KHz i2c-ak39 i2c-ak39: i2c-0: AK39 I2C adapter Linux video capture interface: v2.00 cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource ak_timer5 cs NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. squashfs: version 4.0 (2009/01/31) Phillip Lougher exFAT: Version 1.2.9 jffs2: version 2.2. © 2001-2006 Red Hat, Inc. msgmni has been set to 64 io scheduler noop registered io scheduler cfq registered (default) AK39xx uart driver init, (c) 2013 ANYKA ak39-uart.0: ttySAK0 at MMIO 0x20130000 (irq = 10) is a AK39 ion: failed to create debug files. brd: module loaded loop: module loaded @@@ [akpcm_init]: enter @@@ @@@ [akpcm_probe]: enter @@@ akpcmL0->ak39_codec_probe enter... akpcm probe: mic on akpcm_probe: OK akisp_init Start to init Anyka SPI Flash... Start to init Anyka partition table... AK SPI Driver, (c) 2012 ANYKA akpi regs: SPICON:00000152, SPISTA:00000015, SPIINT:00000000. ak-spi ak-spi: master is unqueued, this is deprecated ak_spi setup the master. pre-scaler=2 (wanted 20Mhz, got 20Mhz) ak spiflash probe enter. pre-scaler=2 (wanted 20Mhz, got 20Mhz) ak_spi_setupxfer,con:00000252. akspi flash ID: 0x00207017 ak-spiflash spi0.0: xm25qh64a (8192 Kbytes) FHA:partition lib version: V1.1.06 FHA:spiflash init FHA:boot block num offset:427 FHA:Sflash_Get_Partition_Startpage g_boot_len:880 mtd_part[0]: name = KERNEL size = 0x200000 offset = 0x39000 mask_flags = 0x1 mtd_part[1]: name = MAC size = 0x1000 offset = 0x239000 mask_flags = 0x1 mtd_part[2]: name = ENV size = 0x1000 offset = 0x23a000 mask_flags = 0x1 mtd_part[3]: name = A size = 0x180000 offset = 0x23b000 mask_flags = 0x1 mtd_part[4]: name = B size = 0x7d000 offset = 0x3bb000 mask_flags = 0x1 mtd_part[5]: name = C size = 0x3b6000 offset = 0x438000 mask_flags = 0x1 Creating 6 MTD partitions on "spi0.0": 0x000000039000-0x000000239000 : "KERNEL" 0x000000239000-0x00000023a000 : "MAC" 0x00000023a000-0x00000023b000 : "ENV" 0x00000023b000-0x0000003bb000 : "A" 0x0000003bb000-0x000000438000 : "B" 0x000000438000-0x0000007ee000 : "C" Init AK SPI Flash finish. akspi master initialize success, use for DMA mode. input: akgpio-keys as /devices/platform/akgpio-keys/input/input0 We're Using Internal RC OSC. AK RTC, (c) 2010 ANYKA i2c /dev entries driver AK MCI Driver (c) 2010 ANYKA akmci_probe : MCI ## MMC Power: GPIO-1 Setup akmci ak_mci.0: Mci Interface driver.mmc0. using l2dma, sw IRQ. detect mode:GPIO detect. akmci_probe : SDIO ## MMC Power: GPIO-1 Setup akmci ak_sdio.1: Mci Interface driver.mmc1. using l2dma, hw IRQ. detect mode:plugin alway. TCP: cubic registered NET: Registered protocol family 17 lib80211: common routines for IEEE802.11 drivers /home/caibin/cam_sdk/nooie_ipc_code_base/kernel/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) VFS: Mounted root (squashfs filesystem) readonly on device 31:4. devtmpfs: mounted Freeing init memory: 108K mount all file system... starting mdev... ************************** Love Linux ! ! ! ************************** 200+0 records in 200+0 records out 102400 bytes (100.0KB) copied, 0.003535 seconds, 27.6MB/s aksensor_module_init f22_set_power_on f22_probe_id id:0xf23 f22_probe_id id:0xf23 NO DEBUG FILE anyka login: /usr/sbin/service.sh: line 202: cmd_serverd: not found start net service...... ## start from nfsroot, do not change ipaddress!