IPL g5f1da5a D-0a SPI 54M 128MB BIST0_0001-OK [SPI_NOR] MXP found at 0x0000a000 offset:00005000 Checksum OK IPL_CUST g5f1da5a runUBOOT() [SPI_NOR] MXP found at 0x0000a000 offset:0000c000 -Decompress BDMA XZ -Decompress BDMA XZ XZ decomp_size=0x00045e3c pvLoadAddr:23d00000 pvRunAddr:23e00000 -Verify CRC32 passed! decomp_size=0x00000000 Disable MMU and D-cache before jump to UBOOT U-Boot 2015.01 (May 17 2021 - 15:20:10) Version: I6g####### I2C: ready DRAM: WARNING: Caches not enabled MMC: MStar SD/MMC: 0 nor_flash_mxp allocated success!! MXIC REMS: 0xC2,0x17 Flash is detected (0x0509, 0xC2, 0x20, 0x18) SF: Detected nor0 with total size 16 MiB MXP found at mxp_offset[0]=0x0000A000, size=0x1000 env_offset=0xB000 env_size=0x1000 MXIC REMS: 0xC2,0x17 Flash is detected (0x0509, 0xC2, 0x20, 0x18) SF: Detected nor0 with total size 16 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: MAC Address Auto-Negotiation... Link Status Speed:10 Full-duplex:1 sstar_emac Warning: sstar_emac using MAC address from net device gpio debug MHal_GPIO_Pad_Set:603 gpio[79] is 1 gpio debug MHal_GPIO_Pad_Set:603 gpio[61] is 1 gpio debug MHal_GPIO_Pad_Set:603 gpio[35] is 1 gpio debug MHal_GPIO_Pad_Set:603 gpio[17] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[1] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[0] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[4] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[64] is 1 gpio debug MHal_GPIO_Pad_Set:603 gpio[65] is 1 gpio debug MHal_GPIO_Pad_Set:603 gpio[64] is 0 SigmaStar # help ? - alias for 'help' aes - Control Mstar AES engine base - print or set address offset bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol btime - Show booting time cmp - memory compare cp - memory copy crc32 - checksum calculation dbg - set debug message level. Default level is INFO dcache - enable or disable data cache debug - Disable uart rx via PAD_DDCA to use debug tool dhcp - boot image via network using DHCP/TFTP protocol dstar - script via SD/MMC eeprom - EEPROM sub-system env - environment handling commands estar - script via network estart - EMAC start fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fatsize - determine a file's size fwupdate- fwupdate command allows to flash vc camera firmware from file on mmc or from memory. go - start application at address 'addr' gpio - Config gpio port help - print command description/usage i2c - I2C sub-system icache - enable or disable instruction cache initDbgLevel- Initial varaible 'dbgLevel' loop - infinite loop on address range macaddr - setup EMAC MAC addr md - memory display mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mssdmmc - Mstar SD/MMC IP Verification System mstar - script via TFTP mw - memory write (fill) mxp - MXP function for Mstar MXP partition nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables reset - Perform RESET of the CPU riu - riu - riu command run - run commands in an environment variable saveenv - save environment variables to persistent storage sdstar - script via sd package secauth - Control Sstar security authenticate sequence setenv - set environment variables sf - SPI flash sub-system sfbin - for uploading sf image to a server(via network using TFTP protocol) sigauth - Only verify digital signature and aes srcfg - sensor pin and mclk configuration. test_sig- Test runAuthenticate2 tftpboot- boot image via network using TFTP protocol uart - UART sub-system version - print monitor, compiler and linker version SigmaStar # printenv baudrate=115200 bootargs=mem=130840K console=ttyS0,115200 LX_MEM=0x7fe0000 mma_heap=mma_heap_name0,miu=0,sz=0x4000000 rootfstype=ramfs mtdparts=NOR_FLASH:320K(boot),64K(tech),5120K(kernel),8192K(app),-(config) hw_type=1210 bootcmd=sf probe 0; sf read 0x22000000 0x60000 0x500000; bootm 0x22000000; setenv bootargs $(bootargs) bkp=1; sf read 0x22000000 0x560000 0x500000; bootm 0x22000000 bootdelay=0 ethact=sstar_emac ethaddr= preboot=gpio output 79 1;gpio output 61 1;gpio output 35 0;gpio output 17 0;gpio output 1 0;gpio output 0 0;gpio output 4 0;gpio output 64 1;gpio output 65 1;gpio output 64 0; stderr=serial stdin=serial stdout=serial Environment size: 683/4092 bytes