U-Boot 2010.06 (Oct 24 2013 - 15:36:07)

NAND:  Special Nand id table Version 1.35
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
0 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0 
hisilicon # <INTERRUPT>

hisilicon # help
?       - alias for 'help'
base    - print or set address offset
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
getinfo - print hardware information
go      - start application at address 'addr'
help    - print command description/usage
loadb   - load binary file over serial line (kermit mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nm      - memory modify (constant address)
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sf      - SPI flash sub-system
tftp    - tftp	- download or upload image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version

hisilicon # printenv
bootdelay=1
baudrate=115200
ethaddr=00:00:23:34:45:66
bootfile="uImage"
filesize=BD7628
fileaddr=82000000
netmask=255.255.255.0
ipaddr=192.168.55.10
serverip=192.168.55.51
bootargs=mem=128M console=ttyAMA0,115200 root=/dev/mtdblock1 rootfstype=jffs2 mtdparts=hi_sfc:3M(boot),13M(rootfs)
bootcmd=sf probe 0;sf read 0x82000000 0x80000 0x280000;bootm 0x82000000
configFlag=ok
cpuFlag=ok
cpuType=3516c
sensorFlag=no
sensorType=32
stdin=serial
stdout=serial
stderr=serial
verify=n
ver=U-Boot 2010.06 (Oct 24 2013 - 15:36:07)

Environment size: 520/262140 bytes

hisilicon # mii dump 1 0
0.     (3100)                 -- PHY control register --
  (8000:0000) 0.15    =     0    reset
  (4000:0000) 0.14    =     0    loopback
  (2040:2000) 0. 6,13 =   b01    speed selection = 100 Mbps
  (1000:1000) 0.12    =     1    A/N enable
  (0800:0000) 0.11    =     0    power-down
  (0400:0000) 0.10    =     0    isolate
  (0200:0000) 0. 9    =     0    restart A/N
  (0100:0100) 0. 8    =     1    duplex = full
  (0080:0000) 0. 7    =     0    collision test enable
  (003f:0000) 0. 5- 0 =     0    (reserved)


hisilicon # 
hisilicon # mii dump 1 1
1.     (7829)                 -- PHY status register --
  (8000:0000) 1.15    =     0    100BASE-T4 able
  (4000:4000) 1.14    =     1    100BASE-X  full duplex able
  (2000:2000) 1.13    =     1    100BASE-X  half duplex able
  (1000:1000) 1.12    =     1    10 Mbps    full duplex able
  (0800:0800) 1.11    =     1    10 Mbps    half duplex able
  (0400:0000) 1.10    =     0    100BASE-T2 full duplex able
  (0200:0000) 1. 9    =     0    100BASE-T2 half duplex able
  (0100:0000) 1. 8    =     0    extended status
  (0080:0000) 1. 7    =     0    (reserved)
  (0040:0000) 1. 6    =     0    MF preamble suppression
  (0020:0020) 1. 5    =     1    A/N complete
  (0010:0000) 1. 4    =     0    remote fault
  (0008:0008) 1. 3    =     1    A/N able
  (0004:0000) 1. 2    =     0    link status
  (0002:0000) 1. 1    =     0    jabber detect
  (0001:0001) 1. 0    =     1    extended capabilities


hisilicon # 
hisilicon # mii dump 1 2
2.     (0007)                 -- PHY ID 1 register --
  (ffff:0007) 2.15- 0 =     7    OUI portion


hisilicon # 
hisilicon # mii dump 1 3
3.     (c0f1)                 -- PHY ID 2 register --
  (fc00:c000) 3.15-10 =    48    OUI portion
  (03f0:00f0) 3. 9- 4 =    15    manufacturer part number
  (000f:0001) 3. 3- 0 =     1    manufacturer rev. number


hisilicon # 
hisilicon # mii dump 1 4
4.     (01e1)                 -- Autonegotiation advertisement register --
  (8000:0000) 4.15    =     0    next page able
  (4000:0000) 4.14    =     0    reserved
  (2000:0000) 4.13    =     0    remote fault
  (1000:0000) 4.12    =     0    reserved
  (0800:0000) 4.11    =     0    asymmetric pause
  (0400:0000) 4.10    =     0    pause enable
  (0200:0000) 4. 9    =     0    100BASE-T4 able
  (0100:0100) 4. 8    =     1    100BASE-TX full duplex able
  (0080:0080) 4. 7    =     1    100BASE-TX able
  (0040:0040) 4. 6    =     1    10BASE-T   full duplex able
  (0020:0020) 4. 5    =     1    10BASE-T   able
  (001f:0001) 4. 4- 0 =     1    selector = IEEE 802.3